CTAL-TM-UK : ISTQB Certified Tester Advanced Level - Test Manager (CTAL-TM_UK) Exam

CTAL-TM-UK Dumps
CTAL-TM-UK Braindumps
CTAL-TM-UK Real Questions
CTAL-TM-UK Practice Test
CTAL-TM-UK Actual Questions


iSQI
CTAL-TM-UK
ISTQB Certified Tester Advanced Level - Test Manager
(CTAL-TM_UK)
https://killexams.com/pass4sure/exam-detail/CTAL-TM-UK
Answer: B
QUESTION: 58
Which of the following is NOT a typical key challenge for testing in a RAD based
development approach? 1 credit
A. Re-usable test scripts for (automated) regression testing
B. Project management and control
C. No complete requirements specification
D. Time-boxing
Answer: B
QUESTION: 59
As a result of the RAD based development approach, the test manager has decided to
change the risk mitigation approach. Which test technique might be most appropriate
to use? 2 credits
A. Decision Table Testing
B. Boundary Value Analysis
C. Error Guessing
D. Exploratory Testing
Answer: D
QUESTION: 60
The business has asked for a weekly progress report. Which of the following would
be appropriate as a measure of test coverage? 2 credits
A. Percentage of business requirements exercised
B. Percentage of planned hours worked this week
C. Percentage of countries that have test scenarios
D. Percentage of test iterations completed
Answer: A
Section 11: Sec Eleven (61 to 61)
Details: Topic 11, Scenario 11 "Incident Management"
The following is the current incident handling process in used at the company.
23
Step 1: Incident is documented in the incident Tile with the following information:
- Software module or area where the fault occurred
- Who has reported the fault
- Hardware configuration used for the test that found the fault
- The sequential incident number (1 greater than the last one recorded)
Step 2: Developer assigned to fix the fault
Step 3: Developer fixes the fault
Step 4: Developer signs off the incident as closed, and it is then removed from the
incident file
QUESTION: 61
Regarding the process described above, what is the most important recommendation
you would make using IEEE 1044 as a guide? 2 credits
A. No priority or severity assigned
B. Incident numbering is manual rather than automated
C. No mentioning of reproduceability
D. No classification on type of incident
Answer: A
Section 12: Sec Twelve (62 to 65)
Details: Topic 12, Scenario 12 “Automatic Teller Machine (ATM)”
You are a test manager in charge of integration, system and acceptance testing for a
bank. You are working on a project to upgrade an existing ATM to allow customers
to obtain cash advances from supported credit cards. The system should allow cash
advances from €20 to €500, inclusively, for all supported credit cards. The supported
credit cards are American Express, VISA, Eurocard and Mastercard. In the master
test plan the following items are listed in the section named “items and/or features to
be tested”:
I All supported credit cards
II Language localization
II Valid and invalid advances
IV Usability
V Response time
QUESTION: 62
Relying only on the information provided in the scenario, select the TWO items
and/or features for which sufficient information is available to proceed with test
design. 2 credits
A. All supported credit cards
B. Language localization
C. Valid and invalid advances
24
D. Usability
E. Response time
Answer: A, C
QUESTION: 63
Continuing with the Scenario described in the previous question, which of the
following topics would you need to address in detail in the master test plan? 3 credits
A. An approach to regression testing
B. A list of boundary values for “advance amount”
C. A description of dependencies between test cases
D. A logical collection of test cases
Answer: A
QUESTION: 64
Given the following figures for the testing on a project, and assuming the failure rate
for initial tests remains constant and that all retests pass, what number of tests remain
to be run? 3 credits
A. 700
B. 720
C. 784
D. 570
Answer: B
QUESTION: 65
Given is the following defect removal chart reported at the end of system testing -
showing total defects detected and closed defects (fixed and successfully retested). A
number of open defects are classified as critical. All tests have been executed.
25


Based on the chart above, what is the most appropriate next test phase? 1 credit
A. Acceptance testing to verify the business process
B. Acceptance testing to verify operational requirements
C. Requirements testing as part of testing regulatory compliance
D. Another system test cycle to verify defect resolution
Answer: D


26

User: Liya***** I am extremely grateful to Killexams.com for helping me pass the ctal-tm-uk exam. This is, without a doubt, the most effective system for passing the exam. I started using this study kit three weeks before the exam, and it worked wonders for me. I scored an impressive 89%, which is a testament to the effectiveness of the Killexams.com Questions and Answers. With this study kit, I was able to complete the exam within the allotted time.

User: Alec***** The CTAL-TM-UK questions from killexams.com mirror exactly what the test center gives you in the exam, and their preparation material is excellent. I passed with over 80% thanks to their helpful study guides.

User: Natascha***** It is challenging to find test materials with all the necessary capabilities for the CTAL-TM-UK exam. Luckily, I found killexams.com, which provided comprehensive and useful information. The education and learning of each topic were made seamless through their practice tests, and I urge my friends to use them.

User: Zakhar***** To maintain my position in my current company, passing the exam was necessary, but it was not an easy task. Thankfully, with the help of the question answers and exam simulator, I was able to learn a lot and achieve my certification. I am very grateful for their great work.

User: Emiliano***** Killexams.com studying software helped me rank high among my classmates. The precise and useful information provided in the ctal-tm-uk PDF, ctal-tm-uk practice tests, and ctal-tm-uk books helped me turn into an exceptional student. I am grateful to Killexams.com for providing such helpful resources.

---