HPE6-A66 : Aruba Certified Design Associate (ACDA) Exam

HPE6-A66 Dumps
HPE6-A66 Braindumps
HPE6-A66 Real Questions
HPE6-A66 Practice Test
HPE6-A66 Actual Questions


HP
HPE6-A66
Aruba Certified Design Associate (ACDA)
https://killexams.com/pass4sure/exam-detail/HPE6-A66
Question: 145
When a WLAN has to support nomadic devices, a network architect must primarily plan for which component in their
design?
A. type of users
B. number of users per location
C. mobility requirements and usage
D. density of users
Answer: C
Question: 146
Which two challenges do802.1ig barcode scanners present to a WLAN design? (Select two.)
A. roaming between APs
B. encountering RF interference by devices
C. determining the RF channel bandwidth consumed per Barcode scanner
D. implementing adequate security measures to ensure PCI compliance
E. providing consistent performance on all available channels
Answer: A,D,E
Question: 147
A network architect is creating a new wireless solution for a customer. Wireless coverage is required throughout all
four floors of two buildings on the same campus. Dynamic RF capabilities, including AirMatch, are required. Seamless
roaming is required within and between the two buildings. Each floor will have approximately 20 APs and 6 external
APs are required for connectivity between the two buildings.
A. Given this information, which Aruba solution would be the most cost-effective while still meeting the customer's
requirements? O An IAP cluster per floor
B. A standalone 7008 controller per floor
C. Two 7205 mobility controllers in a cluster
D. Two 7030 mobility controllers in a cluster
Answer: A
Question: 148
Which must you perform in IRIS to assign a device to a Design Group?
A. Right-click the device and select Set Layer Membership
B. Right-click the device and select Set Design Group
C. Drag and drop the device into the Site
D. Drag and drop the device into the Design Group
Answer: D
Question: 149
A network architect is designing a wireless solution for a company that is leasing one floor in a multi-floor building in
a downtown area. The customer is concerned about ensuring complete Wi-Fi coverage and pin-pointing RF hazards.
What type of survey should the network architect perform?
A. Active
B. Virtual
C. Passive
D. Spectrum clearing
Answer: A
Question: 150
A customer placed an order for an ArubaOS 5406R switch and plans to rack mount it in a wiring closet. The
dimensions of the switch are 17.5 inches wide (44.45 cm), 6.9 inches high (17.5 cm), and 17.75 inches deep (45.1 cm).
How many rack units should a customer plan for this switch?
A. 5
B. 4
C. 6
D. 3
Answer: C
Question: 151
A wiring closet with a POE+ switch is 250 feet (76 meters) away from an AP on a building floor. The AP's smart-rate
port is connected to a smart-rate port on the switch, which is capable of 10 Gbps. The cable type is Cat5e STP.
What is the maximum speed that the customer can expect from the connected AP?
A. 2.5 Gbps
B. 1 Gbps
C. 5 Gbps
D. 10 Gbps
Answer: A
Question: 152
A customer has some employees that travel to various locations, where these employees will need Wi-Fi access at
these locations. Because many of these locations do not have wireless support, the employees will need to carry an AP
solution with them. Internet connectivity, if it doesn't exist at these locations, will be provided by a national phone
company USB wireless card which will be connected to AP. The wireless solution needs minimal bandwidth, but
needs to minimally support 802.1 lac wave 1 devices.
Which Aruba AP wireless solution would meet the needs of these employees most effectively and cost efficiently?
A. 318
B. 303H
C. 365
D. 203R
Answer: D
Question: 153
NewStellar has a main corporate campus in a business park with two adjacent buildings. Each building has three floors
and each floor is 322 x 175 feet (98 x 53 meters) for 56,350 square feet (5,235 square meters) total. The ceiling for
each floor is 12 feet (3.6 meters) high with a drop-down ceiling at 10 feet (3 meters).
The network architect has given you one floor to analyze, Building 1 Floor 2, shown in the attached exhibit.


This floor has a central main corridor with washrooms, stairs, elevators and supply and network cabinets. There are
cubicles around the perimeter of the floor. The central part main corridor's dimensions contain 9,350 square feet (870
square meters).
Assuming that wireless coverage is not required in the central area, which square footage (square meter) value should a
network architect use when determining the number of APs in a capacity design for each floor?
A. 55.750 square feet {5,175 square meters)
B. 56.350 square feet {5,235 square meters)
C. 47.000 square feet {4,365 square meters)
D. 338,100 feet {31,410 square meters)
Answer: B
Question: 154
A network architect is redesigning a wireless network. The architect begins by analyzing the number of spatial streams
supported by APs of various vendors as well as the wireless devices currently in the network, if the company wants to
ensure that new wireless design, including user wireless devices, support Multi-User MIMO (MU-MIMO).
Which standard or standards must the wireless products support?
A. Only 802.11ax and 8011.ac
B. Only 802.11ax
C. Only 802.11ax,802.1lac, and 802.l1n
D. Only 802.11ax,802.11ac, 802.11n, and 802.11a
Answer: C
Question: 155
A network architect is given the task to design a new network solution for NewStellar Company, Inc. NewSteiiar has a
main corporate campus in a business park with two adjacent buildings.
The network architect has given one floor to analyze, Building 1 Floor 2, shown in the attached exhibit.


Each building has three floors and each floor is 322 x 175 feet (98 x 53 meters) for 56,350 square feet (5,235 square
meters) total, which results in a total of 338,100 feet (31,410 square meters) for the entire building space. Each floor
has a central main corridor with washrooms, stairs, elevators and supply and network cabinets. There are cubicles
around the perimeter of the floor. The central part main corridor's dimensions contain 9,350 square feet {870 square
meters).
Because of security concerns, video cameras will be installed throughout the facility. There are 16 of these per floor, 8
per wiring closet. The cameras are non-WiFi capable and require POE 802.3af-capable switch ports from which to
draw power.
A wireless capacity design is required. Assuming that wireless coverage is required across the Building 1, Floor 2,
including the central area, and that half the required APs will connect to each wiring closet, approximately how many
POE+ ports will be required per wiring closet for all devices that have POE or POE+ needs?
A. 30
B. 22
C. 42
D. 8
Answer: A
Question: 156
Refer to the exhibit.

When planning the use of Cat7 cabling for a SmartRate connection between an ArubaOS AP and an ArubaOS switch,
which sections should be considered when calculating distance?
A. A + C
B. A + B
C. A + B + C + D
D. A + B + C
Answer: C
Question: 157
A company is redesigning their wireless network and will be upgrading all devices to support the latest wireless
standards. The company is not near any radar installations.
In order to keep wireless NIC power levels as low as possible to reduce interference issues and to take advantage of
radar frequency ranges, what IEEE standard should APs support?
A. 802.11r
B. 802.11 ax
C. S02.11V
D. S02.11h
Answer: B
Question: 158
A network architect has created two sites in IRIS and defined network devices for each site.
From which window would a network architect connect the two sites together?
A. Topology
B. Site-1
C. Catalog
D. Start Page
Answer: B
Question: 159
A network architect is creating a new wired design for a warehouse building.
As a best practice, what length should the architect allow for the service loop in the wiring closets in this environment?
A. 3-10 feet (1-3 m)
B. 3 feet (1 m)
C. 15-30 feet (5-10 m)
D. 30-60 feet (10-20 m)
Answer: B

User: Doris***** I am excited to share the great news that I passed the hpe6-a66 exam yesterday. I would like to thank the entire team at Killexams.com for their excellent work. Their training material is top-notch, and I appreciate the effort they put into creating such high-quality resources.

User: Vivaan***** As I found the subjects for the hpe6-a66 exam troublesome, I relied on Killexams.com questions and answers as a handy reference. The material delivered exactly what I needed, and I am grateful for their assistance. The technique used in this aid was not difficult to understand, and I retained all that I could. I managed to score 92%, a significant improvement from my 1-week battle with the subjects.

User: Nayda***** I scored an excellent 88% on my hpe6-a66 exam using Killexams.com study practice tests. My partner recommended their practice tests as a quick reference, which covered all the material with easy-to-remember answers. I decided to use Killexams.com for all my future tests and was never disappointed.

User: Elena***** I just passed the hpe6-a66 exam with Killexams.com bundle, and it was a great solution for quick yet dependable and valid practice tests. Although Its an expert-level exam, their exam simulator accurately simulates the exam, including the unique question types. It contributed to me getting a 100% score, and I highly recommend it.

User: Tasenka***** The HPE6-A66 exam is not easy, but thanks to Killexams.com, I got the top marks. The HPE6-A66 practice test includes actual exam questions, modern updates, and more. This helped me focus on what I needed to learn without wasting time on unnecessary matters. I used their HPE6-A66 exam simulator, and it made me feel very assured on the exam day. I also posted my marks on my resume and LinkedIn profile, which is a remarkable reputation booster.

---